Did you perform the Washer/Wiper Rear System Check?

--

Go to Step 2

Go to Wiper/Washer System Check

1. Place the ignition switch in the RUN position.
2. Use a J 39200 in order to backprobe from CKT 143 (YEL) cavity E4 at the steering column connector C201 to ground.

Is battery voltage present?

--

Go to Step 3

Go to Step 4

1. Place the ignition switch in the LOCK position.
2. Disconnect the front pulse wiper/washer switch at connector C201.
3. Place the wiper/washer switch in the LO position.
4. Use a J 39200 in order to measure the resistance of the front pulse wiper/washer switch from CKT 96 (GRY) cavity E5 to CKT 143 (YEL) cavity E4 at the C201 connector.

Is the resistance within the specified range?

600ohms-750ohms

Go to Step 5

Go to Step 6

Repair the open in CKT 143 from the front pulse wiper/washer switch at the C201 connector to the instrument panel fuse block.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

1. Ensure that the J 39200 is still connected.
2. Move the front pulse wiper/washer switch from the LO position back through all of the delay settings one step at a time down to the maximum delay setting.

Are the resistance readings within 20% of the specified values respectively?

Go to Step 7

Go to Step 8

Replace the front pulse wiper/washer switch Turn Signal and Multifunction Switch Assembly - Disassemble - Off Vehicle Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .

Is the repair complete?

--

Go to Wiper/Washer System Check

--

1. Reconnect the front pulse wiper/washer switch at the C201 connector.
2. Disconnect the front wiper motor and module.
3. Place the ignition switch in the RUN position.
4. Place the wiper/washer switch in the LO position.
5. Connect a J 39200 between CKT 96 (BRN) cavity E at the front wiper motor and module and ground.

Is battery voltage present?

--

Go to Step 9

Go to Step 11

Replace the front wiper switch Turn Signal and Multifunction Switch Assembly - Disassemble - Off Vehicle Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Connect a J 39200 from the front wiper motor and module CKT 143 (YEL) cavity C and ground.

Is battery voltage present?

--

Go to Step 10

Go to Step 12

Connect a test lampJ 35616-200 from CKT 750 (BLK) cavity B to CKT 143 (YEL) cavity C at the front wiper motor and module.

Does the test lamp light?

--

Go to Step 13

Go to Step 14

Use a J 39200 in order to backprobe the front pulse wiper/washer switch at the C201 connector CKT 96 (BRN) cavity E5 to ground.

Is battery voltage present?

--

Go to Step 15

Go to Step 6

Repair the open in CKT 143 (YEL) between splice S324 and the front wiper motor and module.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Replace the front wiper motor and module Windshield Wiper System Module Replacement .

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Repair the open in CKT 750 (BLK) between the front wiper motor and module and ground.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Repair the open in CKT 96 (BRN) between the front pulse wiper/washer switch and the front wiper motor and module.

Is the repair complete?

--

Go to Wiper/Washer System Check

--