GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Isuzu 🢒 2003 🢒 Ascender - 4WD 🢒 Body and Accessories 🢒 Interior Trim 🢒 Rear Floor Panel Carpet Replacement

Removal Procedure
  1. Remove the front seats. Refer to in Seats.
  2. Remove the second row rear seats. Refer to Rear Seat Replacement in Seats.
  3. Remove the third row rear seats. Refer to Rear Number 2 Seat Replacement in Seats.
  4. Remove the front door sill plates. Refer to Front Side Door Sill Plate Replacement .
  5. Remove the rear door sill plates. Refer to Rear Side Door Sill Plate Replacement .

    6. Notice: Remove the headliner and the headliner harness as an assembly. Do NOT cut or splice the headliner harness. Cutting or splicing the harness may damage the coax cable, resulting in poor radio performance.

  6. Remove the center pillar trim panels. Refer to Center Pillar Garnish Molding Replacement .
  7. Remove the lift gate door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  8. Remove the left/right front body side window garnish molding. Refer to Body Side Rear Window Garnish Molding Replacement .
  9. Remove the left/right rear body side window garnish molding. Refer to Body Side Window Rear Garnish Molding Replacement .
  10. Remove the bolts from the cargo tie-down loops.

    11. Object Number: 798354 Size: SH
  11. Remove the nut (1), securing the stowage jack carrier to the wheelhouse panel.
  12. Loosen the three bolts that secure the jack carrier to the vehicle.
  13. Remove the carpet from around the wheel stud.
  14. Remove the body electrical block. Refer to Rear Electrical Center or Junction Block Replacement in Wiring Systems.
  15. Remove the body electrical block electrical connectors back through the hole in the carpet.
  16. Pull the communication interface module electrical connectors back through the hole in the carpet.
  17. Remove the floor console to the floor console carrier . Refer to Console Replacement in Instrument Panel, Gages and Console.

    18. Object Number: 741605 Size: SH
  18. Remove the four nuts retaining the rear of the floor console bracket to the floor weld studs.
  19. Raise the rear portion of the floor console bracket and remove the carpet from underneath the console bracket.
  20. Remove the carpet from the vehicle.

Installation Procedure

    Object Number: 739850 Size: SH
  1. Position the carpet to the floor panel.

    2. Object Number: 741605 Size: SH
  2. Raise the rear portion of the floor console bracket and slide the carpet underneath the console bracket.
  3. Position the rear carpet over the edge of the front carpet.
  4. Align the holes in the carpet to the seat studs on the floor panel.

    5. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  5. Install the four nuts (2) retaining the rear of the floor console bracket to the floor weld studs.

    6. Tighten
    Tighten the nuts to 25 N·m (18 lb ft).

  6. Feed the bussed electrical center base and the communication interface module electrical connectors through the pass through holes in the carpet.
  7. Install the floor console. Refer to Console Replacement in Instrument Panel, Gages and Console.
  8. Install the center pillar trim panels. Refer to Center Pillar Garnish Molding Replacement .
  9. Install the front side door sill plates. Refer to Front Side Door Sill Plate Replacement .
  10. Pass the communication interface module electrical connectors through the small hole in the carpet.
  11. Pass the body electrical block electrical connectors through the small hole in the carpet.
  12. Install the body electrical block. Refer to Rear Electrical Center or Junction Block Replacement in Wiring Systems.

    13. Object Number: 798360 Size: SH
  13. Install the carpet ensuring that the carpet hooks over the left wheelhouse panel stud.

    14. Object Number: 798354 Size: SH
  14. Install the nut (1) securing the stowage jack carrier to the wheelhouse panel.
  15. Install the right rear quarter lower trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side .
  16. Install the left rear quarter lower trim panel. Refer to Rear Quarter Trim Panel Replacement - Left Side .
  17. Install the left/right rear body side trim rear window garnish molding. Refer to Body Side Window Rear Garnish Molding Replacement .
  18. Install the left/right front body side window garnish molding. Refer to Body Side Rear Window Garnish Molding Replacement .
  19. Install the lift gate door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  20. Install the cargo tie-down loops.

    21. Tighten
    Tighten the cargo tie-down loop bolts to 35 N·m (26 lb ft).

  21. Install the rear side door sill plates. Refer to Rear Side Door Sill Plate Replacement .
  22. Install the second row seats. Refer to Rear Seat Replacement in Seats.
  23. Install the third row seats. Refer to Rear Number 2 Seat Replacement in Seats.
  24. Install the luggage/cargo shade assembly, if equipped.
  25. Install the cargo net, if equipped.
  26. Install the front seats. Refer to in Seats.