Drive Pinion Flange/Yoke and/or Oil Seal Replacement Input Shaft

Tools Required

1. Apply the parking brake.
2. Block the wheels.
3. Remove the rear axle rear unit propeller shaft. Refer to the following list in order to select the correct procedure in Propeller Shaft:

•	One-Piece Propeller Shaft Replacement

•	Two-Piece Propeller Shaft Replacement

•	Three-Piece Propeller Shaft Replacement

•	Four-Piece Propeller Shaft Replacement

•	Tandem Axle Propeller Shaft Replacement

4. Install the J 3453 over the pinion yoke flange.



5. Remove the inter-axle differential input shaft nut and the washer.
6. Using the J 7804-A , remove the inter-axle differential input shaft yoke.
7. Remove the inter-axle differential input shaft seal.
8. Inspect the inter-axle differential input shaft seal surface for damage or scoring. If the seal surface is damaged, replace the inter-axle differential input shaft yoke.

Important: Lubricate the new inter-axle differential input shaft seal lip with the rear axle lubricant. For rear axle lubricant specifications, refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.

1. Apply Silicone Sealer (RTV) GM P/N 1052366 or equivalent to OD of the inter-axle differential input shaft seal.

The silicone sealer will overcome minor faults in the differential carrier seal bore.




2. Install the inter-axle differential input shaft seal.



3. Install the inter-axle differential input shaft yoke.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: 

•	Ensure that the threads are clean and free of grease.

•	Apply 272 Threadlocker GM P/N 12345493 or equivalent to the threads of the inter-axle differential input shaft nut.

4. Install the washer and the new inter-axle differential input shaft nut.

Tighten
Install the J 3453 to secure the yoke and tighten the inter-axle differential input shaft nut to 867 N·m (639 lb ft).

5. If a new inter-axle differential input shaft nut with pre-applied threadlocker is unavailable, the original inter-axle differential input shaft nut may be reused under the following conditions:

•	The nut is in good condition.

•	The threadlocker is applied.

6. Install the rear axle rear unit propeller shaft. Refer to the following list in order to select the correct procedure in Propeller Shaft:

•	One-Piece Propeller Shaft Replacement

•	Two-Piece Propeller Shaft Replacement

•	Three-Piece Propeller Shaft Replacement

•	Four-Piece Propeller Shaft Replacement

•	Tandem Axle Propeller Shaft Replacement

7. Remove the wheel blocks.

Drive Pinion Flange/Yoke and/or Oil Seal Replacement Output Shaft

Tools Required

1. Apply the parking brake.
2. Block the wheels.
3. Remove the differential. Refer to Differential Replacement .
4. Remove the propeller shaft. Refer to the following procedures in Propeller Shaft:

•	One-Piece Propeller Shaft Replacement

•	Two-Piece Propeller Shaft Replacement

•	Three-Piece Propeller Shaft Replacement

•	Four-Piece Propeller Shaft Replacement

•	Tandem Axle Propeller Shaft Replacement




5. Using the J 3453 to secure the yoke, remove the inter-axle differential output shaft nut and washer.
6. Using the J 7804-A , remove the inter-axle differential output shaft yoke.
7. Remove the inter-axle differential output shaft seal.
8. Inspect the inter-axle differential output shaft yoke seal surface for damage or scoring. If the seal surface is damaged, replace the rear propeller shaft yoke.

Important: Lubricate the new inter-axle differential output shaft seal lip with the rear axle lubricant. For rear axle lubricant specifications, refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.

1. Apply Silicone Sealer (RTV) GM P/N 1052366 or equivalent to OD of the inter-axle differential output shaft seal.

The silicone sealer will overcome minor faults in the differential carrier seal bore.




2. Install the inter-axle differential output shaft seal.



3. Install the inter-axle differential output shaft yoke.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: 

•	Ensure that the threads are clean and free of grease.

•	Apply 272 Threadlocker GM P/N 12345493 or equivalent to the threads of the inter-axle differential input shaft nut.

4. Install the washer and the new inter-axle differential output shaft nut.

Tighten
Using the J 3453 to secure the yoke, tighten the inter-axle differential input shaft nut to the torque listed in Fastener Tightening Specifications .

If a new inter-axle differential output shaft nut with pre-applied threadlocker is unavailable, the original inter-axle differential output shaft nut may be reused under the following conditions:

•	The nut is in good condition.

•	The threadlocker is applied.

5. Install the differential Differential Replacement .
6. Install the propeller shaft. Refer to the following procedures in Propeller Shaft:

•	One-Piece Propeller Shaft Replacement

•	Two-Piece Propeller Shaft Replacement

•	Three-Piece Propeller Shaft Replacement

•	Four-Piece Propeller Shaft Replacement

•	Tandem Axle Propeller Shaft Replacement

7. Remove the wheel blocks.