Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Wiper/Washer Schematics Connector End View Reference: Wiper/Washer Connector End Views | |||
1 | Did you perform the Wiper/Washer Diagnostic System Check? | Go to Step 2 | |
2 |
Do the windshield wipers remain in the Park position? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Disconnect the harness connector of the windshield wiper/washer switch. Do the windshield wipers stop? | Go to Step 11 | Go to Step 4 |
4 | Connect a test lamp from the signal circuit of the windshield wiper/washer switch at the BCM to a good ground. Does the test lamp illuminate? | Go to Step 9 | Go to Step 5 |
5 | Connect a test lamp from the supply voltage circuit of the Wiper 2 relay coil to a good ground. Does the test lamp illuminate? | Go to Step 14 | Go to Step 6 |
6 | Connect a test lamp from the control circuit of the windshield washer pump to a good ground. Does the test lamp illuminate? | Go to Step 15 | Go to Step 7 |
7 | Disconnect the Wiper 1 relay. Do the windshield wipers stop? | Go to Step 8 | Go to Step 16 |
8 | Connect a test lamp from the supply voltage circuit of the Wiper 1 relay coil from the BCM to a good ground. Does the test lamp illuminate? | Go to Step 10 | Go to Step 12 |
9 | Test the signal circuit of the windshield wiper switch for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 13 |
10 | Test the supply voltage circuit of the Wiper 1 relay for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 13 |
11 | Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 17 |
12 | Inspect for poor connections at the Wiper 1 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 18 |
13 | Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 19 |
14 | Repair a short to voltage on supply voltage circuit of the Wiper 2 relay coil. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
15 | Repair a short to voltage on control circuit of the windshield washer pump. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
16 | Repair a short to voltage on high speed circuit of the windshield wiper motor. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
17 | Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement . Did you complete the replacement? | Go to Step 20 | -- |
18 | Replace the Wiper 1 relay. Did you complete the replacement? | Go to Step 20 | -- |
19 |
Important: Perform the programming or setup procedure for the control module if required. Replace the BCM. Refer to Body Control Module Replacement in Body Control System. Did you complete the replacement? | Go to Step 20 | -- |
20 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 |